Hello,
I purchased the HDMI CEC adapter so that I could fully control my WMC HTPC with my new TV's remote.
I've installed all the latest drivers and apps, and while the basics do work (up, down, left, right), all the transport controls (play, pause, FF, RW, Skip Forward, Skip Back) do not work at all.
Has anyone else had a similar problem? Any suggestions on how to fix?
I've tried looking at EventGhost as a way around the problem, but I get errors when installing the CECLib plug-in.
Help???
Thx!
Jon
Problems with Pulse-Eight HDMI CEC adapter
-
- Posts: 52
- Joined: Mon Aug 01, 2011 9:46 pm
- Location:
- HTPC Specs:
-
- Posts: 1477
- Joined: Mon Aug 20, 2012 6:52 pm
- Location:
- HTPC Specs:
It's possible your TV doesn't pass those commands over HDMI. It would be much cheaper and simpler to simply get a universal remote. You can get a really good one for one third of the price of that adapter. Such a remote would control every aspect of your entire home theater.
Otherwise, you'll have to figure out the libCEC thing before you can go any farther.
Otherwise, you'll have to figure out the libCEC thing before you can go any farther.
-
- Posts: 52
- Joined: Mon Aug 01, 2011 9:46 pm
- Location:
- HTPC Specs:
The TV is passing the commands. It's just what the commands are mapped to on my PC are not triggering the events. When I go into the tray app and try to change what commands the TV remote events trigger to ones that I know work like (arrow left), even they are not triggering.mdavej wrote:It's possible your TV doesn't pass those commands over HDMI. It would be much cheaper and simpler to simply get a universal remote. You can get a really good one for one third of the price of that adapter. Such a remote would control every aspect of your entire home theater.
Otherwise, you'll have to figure out the libCEC thing before you can go any farther.
The whole point of going this route is to combine my TV and WMC remote into a single interface. I'm very close. This is the last piece of the puzzle!
Thx.
Jon
-
- Posts: 52
- Joined: Mon Aug 01, 2011 9:46 pm
- Location:
- HTPC Specs:
OK, I don't know what happened, but now I think I'm in trouble.
So, suddenly, the Pulse Eight transport controls are now kind of working. Not perfectly, but they are working with the original TV remote. Oddly, they are not working when the exact same commands are loaded into my Universal Remote (Harmony 880).
But the more concerning development is that my IR receiver for Win 7 is no longer controlling WMC! I can ONLY control WMC via CEC. Yesterday, I could use the Win 7 IR receiver as required, and some of the CEC commands via TV remote. Today, I am unable to get any "normal" IR commands to control WMC!
What did I do? What can I do to return WMC back to normal where it responds to IR commands?
Any help appreciated... I'm kind of freaking out now because my little experiment with CEC has now cost me a system that I simply cannot control at all via remote.
Thx.
Jon
PS - I uninstalled EventGhost in case that was the culprit. Didn't help. I tried removing the Pulse-Eight Device from my environment. Didn't help. The IR driver in Devices is fine - it's installed and has the driver assigned to it as normal.
So, suddenly, the Pulse Eight transport controls are now kind of working. Not perfectly, but they are working with the original TV remote. Oddly, they are not working when the exact same commands are loaded into my Universal Remote (Harmony 880).
But the more concerning development is that my IR receiver for Win 7 is no longer controlling WMC! I can ONLY control WMC via CEC. Yesterday, I could use the Win 7 IR receiver as required, and some of the CEC commands via TV remote. Today, I am unable to get any "normal" IR commands to control WMC!
What did I do? What can I do to return WMC back to normal where it responds to IR commands?
Any help appreciated... I'm kind of freaking out now because my little experiment with CEC has now cost me a system that I simply cannot control at all via remote.
Thx.
Jon
PS - I uninstalled EventGhost in case that was the culprit. Didn't help. I tried removing the Pulse-Eight Device from my environment. Didn't help. The IR driver in Devices is fine - it's installed and has the driver assigned to it as normal.
-
- Posts: 200
- Joined: Sat Jun 09, 2012 3:33 am
- Location:
- HTPC Specs:
Did you ever figure this thing out? I got the adapter for my nuc and I can't use channel up on my remote
-
- Posts: 52
- Joined: Mon Aug 01, 2011 9:46 pm
- Location:
- HTPC Specs:
I had to reinstall event ghost but remove all plugins.